Glass processing

Glass is transparent and brittle: conventional and thermal methods chip it, crack it, and leave tapered walls. Femtosecond laser pulses deposit energy faster than heat can spread, so glass can be drilled into high-aspect-ratio vias, milled and cut with smooth walls, scribed kerf-free by Bessel beams, or modified for selective chemical etching.

Material processing
Material processing Glass Metal Polymer Other materials
Glass

Thin glass cutting

Glass substrates thinner than 0.5 mm are fragile and crack readily under thermal load. The ultra-short pulse duration of a femtosecond laser keeps thermal accumulation low, which is what allows cutting, milling and drilling at this thickness.

The FemtoLux allows processing parameters to be tuned to each glass type, so one system covers borosilicate, fused silica and thin cover slips. Cut edges, milled features and 300 µm drilled holes all come out with minimal chipping and no cracking.

300 µm hole drilling in thin borosilicate glass.

300 µm hole drilling in thin borosilicate glass.

Courtesy of FTMC.

Manufacturing examples

Scanning electron microscope image of drilled 300 µm holes in borosilicate glass.

Scanning electron microscope image of drilled 300 µm holes in borosilicate glass.

Courtesy of FTMC.

Fused-silica milling.

Fused-silica milling.

Courtesy of FTMC.

Thin fused-silica cutting.

Thin fused-silica cutting.

Courtesy of FTMC.

Thin cover slip hole drilling.

Thin cover slip hole drilling.

Courtesy of Laser Micromachining Ltd.

Recommended products

FemtoLux
Industrial Femtosecond Lasers
  • 50 W / >300 µJ at 1030 nm
  • 20 W / >50 µJ at 515 nm
  • 10 W / >25 µJ at 343 nm
  • < 400 fs – 1 ps
  • Single shot to 4 MHz (AOM controlled)
  • MHz, GHz, MHz+GHz burst modes

Similar applications

GHz burst assisted percussion drilling of high aspect ratio holes in EXG glass.
Through-glass vias (TGVs) fabrication

Forming high-aspect-ratio holes in glass substrates is becoming more important, especially in the semiconductor field. Femtosecond lasers can form low-taper, high-aspect-ratio TGVs in glass at high quality, with low chipping, no cracking, and a smooth inner hole wall.
UVFS milling.
Glass milling in GHz burst mode

Femtosecond milling of glass gives high quality but limited throughput. GHz burst mode on the industrial femtosecond laser FemtoLux splits one high-energy pulse into a train of sub-pulses, and 70 pulses at a 2 GHz intra-burst rate deliver sevenfold throughput over single-pulse mode.
Bottom-up milling of 200 µm holes in SCHOTT BF33/D263 glass.
Bottom-up milling of glass

Conventional laser milling struggles to achieve high aspect ratio geometries, because ablation debris accumulates in the ablation area and prevents further material removal. Bottom-up milling focuses the laser beam at the bottom of the sample, so all ablation products leave through the backside and deep, taper-free geometries can be formed in glass.
Micro-lens array fabricated with hybrid laser processing method using the FemtoLux 30
Hybrid laser processing of micro-lens arrays

A micro-lens array is fabricated with hybrid laser processing: burst mode combined with bottom-up milling. The device base is cut from a thick fused-silica plate, the lens array is ablated on its surface, and CO₂ laser polishing brings it to optical quality. The same route suits other custom micro-optical elements.
Laser-based Bessel beam scribing of 4.8 mm soda-lime glass.
Laser-based Bessel beam scribing

Conventional glass cutting removes material and leaves a kerf. Bessel beam scribing does not: a single femtosecond laser pass writes a line of voids inside the glass, and the part then separates mechanically or thermally. On 4.8 mm soda-lime glass, sidewall roughness stays below 0.5 µm at 80 mm/s.
Femtosecond laser-induced selective etching of various-diameter holes in fused silica.
Femtosecond laser-induced selective etching

Femtosecond laser-induced selective etching is a two-step process: focused pulses modify the material structure, and a chemical etch then removes only the modified regions. It produces taper-free 3D features in transparent materials, with surface roughness in the hundreds of nanometers, and it works at wafer scale.
All applications